How to Make 20ml at 50mg/ml of Injectable Winstrol in Oil Step by Step?

Winstrol - Stanozolol is a very commonly used anabolic steroid for cutting cycles. Do you know how to cook it right? Following is direction.

Tip:

Only try to convert winstrol powder 1 gram at a time, it is very easy to ruin it in the conversion.

Supplies:

1 Gram winstrol
1 20 ml glass vial or larger
1 20 ml sterile glass vial or larger
1 .45 Whatman sterile syringe filter.
2 5 or 10 ml syringes
2 3 ml syringes
3 18 or 20 gauge pins
2 22 gauge pins
17 ml of sesame seed oil
0.2 ml of benzyl alcohol
2 ml of guaiacol (super solvent)

Procedure

Step 1
Weigh out 1 gram of winstrol powder, you will need a scale. Use the tare function to take away the weight of the container that holds your powder, and weigh it out to 1 gram.

Step 2
Draw out 2 ml of the super solvent, using 1 of the 3 ml syringes.

Step 3
Place the powder in the open glass vial, then add the super solvent to the powder in the vial.

Step 4

A: Place back on rubber stopper, put one of the 20g pins in the stopper. Place the vial in a small pan, and place on eye of the stove (you can do this step in the oven, but this method works better). Cut on heat, heat until powder disolves into a liquid (the melting point of winstrol is between 239.8-242 degrees F). Turn off heat, and let it cool down still in the pan, until it reaches room temp. again takes about 15 minutes.

B: Also heat seseame oil (heat more than 17ml because you won't get it all out) it can be heated on a stove eye, or in the oven, the oil needs to reach 212 F., to help sterilize the oil. You'd better put it in the oven at 275 F. Just to make sure.

Step 5

Draw out 0.2 ml of benzyl alcohol, this is 1% of the final solution. It is very important that you do not use more than 1% of the solution with winstrol, or it could crash when finished.

Step 6

Add BA to the solution in the vial. Shake very gently.

Step 7

A: Draw out the oil with the 10 ml syringe, (Be sure you have allowed it to cool down some) add the 15ml of oil to the solution. Shake very gently again.

Note - After adding the oil to the solution the winstrol may begin to clump up back into a powder, if it does, you just need to reheat it again like in Step 4a, remember to let it cool slowly.

B: Save 2 ml of oil in the syringe, and re-cap it. You need this later during the sterile filter process to make sure none of the winstrol is left in the filter.

Step 8

Place 1 of the 18 guage pins in the steile unopened vial, and attach the whatman sterile filter. Draw out the solution using the other 10ml syringe, attach to the filter, and slowly press solution into the sterile vial. Then use the remainding 2ml of oil in the other syringe, to run through the filter, to make sure that none of the winstrol is left in the filter.

Step 9

After filtering, leave the pin in the sterile vial, remove the filter. Place the vial in a small pan, and place on eye of the stove (you can do this step in the oven, but this method works better). Cut on heat, heat solution for about 15 to 20 minutes. Turn off heat, and let it cool down still in the pan, until it reaches room temp. again this takes about 15 minutes. Your finished product should be a light gold color.

Sincerely hope this direction could help you with homebrew.

Greeting

Team of Landmarkchem